CB22, CB24, CB32 and CC24 Utility Compactors Plate Locations and Film Locations Caterpillar


Plate Locations and Film Locations
`
1.1. Product Identification Number (PIN)
2.1. Eurasian Economic Union
3.2. Manufacturer Information
4.1. Certification
5.2. ROPS/FOPS Structure
6.2. European Union
7.2. Sound Certification
8.2. Product Link

The Product Information Number (PIN) will be used to identify a powered machine that is designed for an operator to ride.

AVSpare products such as engines, transmissions and major attachments that are not designed for an operator to ride are identified by Serial Numbers.

For quick reference, record the identification numbers in the spaces that are provided below the illustration.

Product Identification Number (PIN)



Illustration 1g01413950

Machine PIN____________________



Illustration 2g01413956

Engine Information and Serial Number Plate____________________

Eurasian Economic Union

For machines compliant to the Eurasian Economic Union requirements, the EAC mark plate is positioned near the Product Identification Number (PIN) plate (see Product Information Section of the machine Operation and Maintenance Manual). The EAC mark plate is placed on machines certified to the Eurasian Economic Union requirements effective at the time of market entry.



Illustration 3g06094564

The Month and Year of Manufacture are on the PIN plate.

Manufacturer Information

Manufacturer:

AVSpare Paving Products Inc.,
9401 85 th Avenue North
Brooklyn park MN, 55445-2199

Entity authorized to communicate on request as required by Customs Union Technical Regulations of the Eurasian Economic Union:

AVSpare Eurasia LLC
75, Sadovnicheskaya Emb.
Moscow 115035, Russia

Certification

ROPS/FOPS Structure

This message is positioned on the ROPS on the left side of the machine above the door.



Illustration 4g00932470

------ WARNING! ------

Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. This will void the certification. Consult your Cat dealer to determine this structure's limitations without voiding its certification.


This machine has been certified to the standards that are listed on the certification film. The maximum mass of the machine, which includes the operator and the attachments without a payload, should not exceed the mass on the certification film.

Refer to Operation and Maintenance Manual, "Guards (Operator Protection)" for more information.

European Union



Illustration 5g01880193

This plate is positioned on the bottom left side of the plate for the PIN.

Note: The CE plate is on machines that are certified to the European Union requirements that were effective at that time.

For machines compliant to 2006/42/EC, the following information is stamped onto the CE plate. For quick reference, record this information in the spaces that are provided below.

  • Engine Power Primary Engine (kW)____________________

  • Engine Power for Additional Engine (If Equipped) ____________________

  • Typical Machine Operating Weight for European Market (kg)____________________

  • Year of Construction____________________

  • Machine Type ____________________


Illustration 6g01120192

This plate is positioned on the bottom left side of the plate for the PIN.

Note: The CE plate is on machines that are certified to the European Union requirements that were effective at that time.

For machines compliant to 1998/42/EC, the following information is stamped onto the CE plate. For quick reference, record this information in the spaces that are provided below.

  • Engine Power Primary Engine (kW)____________________

  • Typical Machine Operating Weight for European Market (kg)____________________

  • Year____________________

For the name and address of the manufacturer, and the country of origin of the machine, refer to the PIN plate.

For manufacturer name and address and the country of origin, see the PIN plate.

Sound Certification



Illustration 7g00933634
A typical example of this film is shown. Your machine may have a different value.

If equipped, the certification film is used to verify the environmental sound certification of the machine. The value that is listed on the film indicates the guaranteed sound power level. The guaranteed sound power level is measured at the time of manufacture. The guaranteed sound power level is measured according to the conditions that are specified in "ISO 6394:1998".

Product Link

If equipped, this message is used to verify the certification of the Product Link as a RF transmitter. The following specifications are provided to aid in ensuring compliance with all local regulations:

Table 1
Operating frequency range  148 to 150 MHz 
Transmitter power  5 Watts 

This message is located on the control group for the Product Link. The control group is located on the top of the cab.



Illustration 8g01261742

------ WARNING! ------

This machine is equipped with a Cat Product Link radio communication device which must be deactivated within 6.0 m (20 ft) of a blast zone. Failure to do so could result in serious injury or death.


If the machine is required to work within 6 m (20 ft) of a blast area, power to the Product Link module must be disconnected.

Consult your AVSpare dealer with any questions that concern the operation of the Product Link in a specific country.

Information System:

CB22, CB24, CB32 and CC24 Utility Compactors Specifications
CB22, CB24, CB32 and CC24 Utility Compactors Sound Information and Vibration Information
CB22, CB24, CB32 and CC24 Utility Compactors Safety Messages
140M and 150 Motor Grader Control Manifold (Steering Backup) - Install
140M and 150 Motor Grader Control Manifold (Steering Backup) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Drum Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
140M and 150 Motor Grader Steering Control Valve - Install
140M and 150 Motor Graders Engine Supplement Radiator Guard and Support, Aftercooler, Hydraulic Oil Cooler, and Radiator, - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
R1600G Load Haul Dump Machine Electrical System Actual Gear Indicator
R1600G Load Haul Dump Machine Electrical System Engine Stop
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Axle Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
2007/10/01 A New Transmission Speed Sensor is Now Available for Series H-Series Motor Graders {3175}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
Replacement of the Blower Assembly on Certain Wheel Loaders{7304, 7320}
2007/10/08 A New Main Power Relay, Starter Relay and Glow Plug Relay are Now Used {1403, 1412, 4493, 7499}
2007/10/08 A New Main Power Relay and Starter Relay are Now Used {4493, 7499}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
The Electronic Priming Pump for Machine Engines will not Prime{1258, 1263}
279C, 289C and 299C Compact Track Loaders Reference Material