CB22, CB24, CB32 and CC24 Utility Compactors Safety Messages Caterpillar


Safety Messages
`
1.1. Do Not Operate (1)
2.1. Seat Belt (2) (If Equipped)
3.1. Do Not Weld or Drill (3) (If Equipped)
4.1. Crush Hazard (4)
5.1. Crush Hazard (5)
6.1. Crush Hazard (6)
7.1. Batteries (7)
8.1. Pressurized System (8)

There are several specific safety messages on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all safety messages.

Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the safety messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.

Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a safety message on the replacement part. Any AVSpare dealer can provide new safety messages.



Illustration 1g01413908

Do Not Operate (1)

This safety message is located below the steering wheel.



Illustration 2g01370904

------ WARNING! ------

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any AVSpare dealer for replacement manuals. Proper care is your responsibility.


Seat Belt (2) (If Equipped)

This safety message is located on the post for the ROPS.



Illustration 3g01370908

------ WARNING! ------

A seat belt should be worn at all times during machine operation to prevent serious injury or death in the event of an accident or machine overturn. Failure to wear a seat belt during machine operation may result in serious injury or death.


Do Not Weld or Drill (3) (If Equipped)

This safety message is located on the post for the ROPS (Rollover Protective Structure).



Illustration 4g01226901

------ WARNING! ------

Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification.


Crush Hazard (4)

This safety message is located on both sides of the machine at the rear of the hood.



Illustration 5g01412530

------ WARNING! ------

A crushing hazard exists between the front frame and rear frame when the machine is articulated. This can result in personal injury. Keep your feet inside the operator station.


Crush Hazard (5)

This safety message is located on both sides of the machine near the articulation joint.



Illustration 6g01371644

------ WARNING! ------

Stay back a safe distance. No clearance for a person in this area when the machine turns. Severe injury or death from crushing could occur.


Crush Hazard (6)

This safety message is located on both sides of the machine near the articulation joint.



Illustration 7g01371647

------ WARNING! ------

Connect the steering frame lock between the front and the rear frames before lifting, transporting, or servicing the machine in the articulation area. Disconnect the steering frame lock and secure the steering frame lock before resuming operation. Severe injury or death could occur.


Batteries (7)

This safety message is located on the left side of the machine above the drum.



Illustration 8g01370909

------ WARNING! ------

Explosion Hazard! Improper jumper cable connections can cause an explosion resulting in serious injury or death. Batteries may be located in separate compartments. Refer to the Operation and Maintenance Manual for the correct jump starting procedure.


Pressurized System (8)

This safety message is located in the engine compartment on top of the radiator.



Illustration 9g01371640

------ WARNING! ------

Pressurized system: Hot coolant can cause serious burn. To open cap, stop engine, wait until radiator is cool. Then loosen cap slowly to relieve the pressure.


Information System:

140M and 150 Motor Grader Control Manifold (Steering Backup) - Install
140M and 150 Motor Grader Control Manifold (Steering Backup) - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Drum Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
140M and 150 Motor Grader Steering Control Valve - Install
140M and 150 Motor Graders Engine Supplement Radiator Guard and Support, Aftercooler, Hydraulic Oil Cooler, and Radiator, - Install
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
R1600G Load Haul Dump Machine Electrical System Actual Gear Indicator
R1600G Load Haul Dump Machine Electrical System Engine Stop
R1600G Load Haul Dump Machine Electrical System Engine Start
R1600G Load Haul Dump Machine Electrical System Engine Start (Remote Control)
R1600G Load Haul Dump Machine Electrical System Autoshift Control (STIC Steering)
CB22, CB24, CB32 and CC24 Utility Compactors Sound Information and Vibration Information
CB22, CB24, CB32 and CC24 Utility Compactors Specifications
CB22, CB24, CB32 and CC24 Utility Compactors Plate Locations and Film Locations
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Piston Pump Neutral (Axle Propel Pump) - Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Drum Propel) - Test and Adjust
2007/10/01 A New Transmission Speed Sensor is Now Available for Series H-Series Motor Graders {3175}
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Pump Control (Manual Displacement Control) Neutral (Axle Propel) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Neutral Start Switch - Test and Adjust
Replacement of the Blower Assembly on Certain Wheel Loaders{7304, 7320}
2007/10/08 A New Main Power Relay, Starter Relay and Glow Plug Relay are Now Used {1403, 1412, 4493, 7499}
2007/10/08 A New Main Power Relay and Starter Relay are Now Used {4493, 7499}