3500 Generator Sets Emergency Stopping Caterpillar


Emergency Stopping
`
1.1. Emergency Stop Button
2.1. Air Shutoffs (If Equipped)


NOTICE

Emergency shutoff controls are for EMERGENCY use ONLY. DO NOT use emergency shutoff devices or controls for normal stopping procedure.


Ensure that any components for the external system that aid the engine operation are secured after the engine is stopped.

Emergency Stop Button

Use of the emergency stop will shut off the fuel. If the engine is equipped with air shutoffs, the air shutoffs will also be activated.


NOTICE

Do not start the engine until the problem necessitating the emergency stop has been located and corrected.


It may be necessary to reset the emergency stop button before the engine can be restarted.

If the emergency stop button is used, both of the air shutoffs must be reset before the engine can be restarted.

The power for the ECM must be cycled before the engine can be restarted.

Air Shutoffs (If Equipped)

The reset mechanisms for the air shutoffs in your 3500 Engine may look like one of the following reset mechanisms.



Illustration 1g01676674

The air shutoffs are activated by oil pressure when energy to a solenoid is interrupted. Each air shutoff uses a plate that rotates on a shaft in order to shut off inlet air to the aftercooler. The engine stops because of the restricted air supply to the combustion chamber. The air shutoffs will actuate for the following conditions:

  • The emergency stop button is pressed.

  • The air shutoff is activated.

  • An overspeed shutdown occurs.

  • The electronic control module loses power.

To reset the air shutoff on earlier models, turn the reset knob to the "OPEN" position. To reset the air shutoff on later models, turn the hex until the indicator is at the "OPEN" position.

Ensure that both of the air shutoffs are resetbefore starting the engine. Ensure that the cause of the emergency stop is repaired before starting the engine.

Information System:

140M and 150 Motor Graders Engine Supplement Flywheel and Rear Gear Group - Remove and Install - Drive Gear
CB34, CB34XW and CC34 Utility Compactors Parking Brake Manual Release
CCS7 Compactor Machine Systems Articulating and Oscillating Hitch
2007/10/22 The Power Train Oil Lines Group is Updated {3016, 3154}
2008/12/15 The Control Assembly is Updated in the Cab {7304, 7320, 7451}
CB34, CB34XW and CC34 Utility Compactors Towing the Machine
CB34, CB34XW and CC34 Utility Compactors Lifting and Tying Down the Machine
C32 LRC Engine for Track-Type Tractors Electrical Connectors
3500 Generator Sets Air Shutoff - Test - Engines That Are Equipped with ADEM II or ADEM III Engine Control Modules (If equipped)
140M and 150 Motor Grader Piston Pump (Hydraulic Fan) - Assemble
160M and 160 Motor Grader Power Train Front Axle - Install
140M and 150 Motor Grader Piston Pump (Hydraulic Fan) - Disassemble
140M and 150 Motor Graders Engine Supplement Radiator Guard and Support, Aftercooler, Hydraulic Oil Cooler, and Radiator - Remove
140M and 150 Motor Graders Engine Supplement Water Pump - Remove and Install
Installing the 311-8705 Machine Enclosure Seal Kit (DEBRIS BARRIER){7276, 7276}
2008/04/21 A New Cover for the Rotor Transmission is Now Used on Reclaimer Mixers {3064}
785D OEM Off-Highway Truck Battery Disconnect Switch
PL61 Pipelayer Safety Messages - PL61 Pipelayer
140M and 150 Motor Grader Blade Lift Arm - Remove
140M and 150 Motor Grader Blade Lift Arm - Install
140M and 150 Motor Grader Steering Control Valve - Remove
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Compactors Propel System Relief Valve (Main, Axle Propel Pump) - Test and Adjust
R1600G Load Haul Dump Machine Systems Ejector Bucket - Disassemble
CB34, CB34XW and CC34 Utility Compactors Belts - Inspect/Adjust/Replace