143H and 163H Motor Graders Wheel Bearing Oil Sample (Front) - Obtain - If Equipped Caterpillar


Wheel Bearing Oil Sample (Front) - Obtain - If Equipped
`
143H and 163H Motor Graders [SEBU7473]
FRAME AND BODY
AXLE GP
143H and 163H Motor Graders Wheel Bearing Oil (Front) - Change - If Equipped
143H and 163H Motor Graders Wheel Bearing Oil Sample (Front) - Obtain - If Equipped

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




Illustration 1g01271804
Typical example
The wheel has been removed for ease of viewing.

The wheel bearing sample plug (1) is located on the inner side of each front wheel of the machine.

Refer to Special Publication, SEBU6250, "S·O·S Services Oil Analysis" for information that pertains to obtaining a sample of the oil. Refer to Special Publication, PEHP6001, "How To Take A Good Oil Sample" for more information about obtaining a sample of the hydraulic oil.

After sample has been obtained, ensure that oil is at proper level. Refer to Operation and Maintenance Manual, "Wheel Bearing Oil Level (Front) - Check".

Information System:

CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Main, Drum Propel Pump) - Test and Adjust
770 and 772 Off-Highway Trucks Power Train Transfer Gears - Assemble
770 and 772 Off-Highway Trucks Power Train Transfer Gears - Disassemble
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Axle Propel Pump) - Test and Adjust
3176C Engine for the R1600G and the R1700G Load Haul Dumps Shutdown - Test
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Drum Propel Pump) - Test and Adjust
CS54 and CP54 Vibratory Soil Compactors Lubricant Viscosities
140M and 150 Motor Graders Engine Supplement Refrigerant Compressor - Remove and Install
CP76 and CS76 Vibratory Compactors Machine Systems Piston Motor (Vibratory) - Test - Cooling Valve
CP56, CP64, CP74, CS56, CS64 and CS74 Paving Compactors Machine Systems Axle Housing (Parking Brake, Differential and Bevel Gear) - Assemble
CP56, CP64, CP74, CS56, CS64 and CS74 Paving Compactors Machine Systems Axle Housing (Parking Brake, Differential and Bevel Gear) - Disassemble
140M and 150 Motor Graders Engine Supplement Refrigerant Condenser - Remove and Install
CS54 and CP54 Vibratory Soil Compactors Engine Air Filter Primary Element - Clean/Replace
2007/09/17 Additional Parts are Available for the Filler Cap {3177, 4332, 5056}
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Remove
3176C Engine for Caterpillar Built Machines Injector Solenoid - Test
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Install
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Disassemble
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Assemble
Wiring the 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED){1421, 1901, 7490}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Sensor Signal (Analog, Active) - Test
C4.4 (Mech) Industrial Engine Fuel System Pressure - Test
16M Motor Grader Operator Controls
140M and 150 Motor Graders Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install