NO. 16 MOTOR GRADER Every 50 Service Hours Or Weekly Caterpillar


Every 50 Service Hours Or Weekly
`
1.1. (4)Ball And Socket Joints
2.1. (5)Blade Lift Shafts
3.1. (6)Circle Reverse Shaft Bearing
4.1. (7)Blade Lift Input Shaft Support Bearings
5.1. (8)Center Shift Pinion And Rail
6.1. (9)Circle Guide Shoes
7.1. (10)Circle Draft Ball Joint
8.1. (11)Axle Pivot Pin Bearings
9.1. (12)Steering Gear Shaft - Steering Arm Block
10.1. (13)Tie Rod End (Inner)
11.1. (14)Tie Rod Fork, Block And Wheel Lean Bar
12.1. (15)Lean Arm And Cylinder Pivot Pins
13.1. (16)Axle Pivot Pin
14.1. (17)Wheel Lean Bar And Arm Pivot Pin
15.1. (18)Steering Cylinder Support
16.1. (19)Blade Tip Pivots
17.1. (20)Blade Tip Cylinder Support Bearings
18.1. (21)Power Blade Cylinder Rod
19.1. (22)Transfer Gear Drive Shaft
20.1. (23)Ripper-Scarifier Trunnion Block Bearings
21.1. (24)Ripper-Scarifier Linkage Pins
22.1. (25)Top Of Circle

(4)Ball And Socket Joints

Lubricate joints on each end of lift links and center shift link. Total 6 fittings (49G1-49G811).

(5)Blade Lift Shafts

Lubricate rear bearings on blade lift shafts. Total 2 fittings.

(6)Circle Reverse Shaft Bearing

Lubricate bearing at rear of shaft. 1 fitting.

(7)Blade Lift Input Shaft Support Bearings

Lubricate shaft bearings under frame, ahead of center shift rack. Total 2 fittings.

(8)Center Shift Pinion And Rail

Lubricate pinion at bottom of shaft. Lubricate rail at rear. Total 3 fittings.

(9)Circle Guide Shoes

Lubricate on bottom side. Total 6 fittings.

(10)Circle Draft Ball Joint

Lubricate 1 fitting on each side of cap. Total 2 fittings. (49G1-49G811).

(11)Axle Pivot Pin Bearings

Lubricate at center of axle, ahead of center tie rod ends. 1 fitting.

(12)Steering Gear Shaft - Steering Arm Block

Lubricate shaft in front of block. Lubricate block at top and rear. Total 4 fittings.

(13)Tie Rod End (Inner)

Lubricate at side and rear of forks. Total 4 fittings.

(14)Tie Rod Fork, Block And Wheel Lean Bar

Lubricate fork on top side, and block at rear of spindle, at both wheels. Total 4 fittings.

Lubricate left wheel lean bar and arm pivot pin at front. Total 2 fittings.

(15)Lean Arm And Cylinder Pivot Pins

Lubricate right wheel lean arm at front. 1 fitting.

Lubricate wheel lean cylinder pivots on end of cylinder and rod. Total 3 fittings.

(16)Axle Pivot Pin

Lubricate at center of axle, at front. 1 fitting.

(17)Wheel Lean Bar And Arm Pivot Pin

Lubricate right wheel lean bar at front. 1 fitting.

(18)Steering Cylinder Support

Lubricate at top and bottom. Total 2 fittings.

(19)Blade Tip Pivots

Lubricate pivots at rear of blade on both sides. Total 2 fittings.

(20)Blade Tip Cylinder Support Bearings

Lubricate each cylinder at top and rod end. Total 4 fittings.

(21)Power Blade Cylinder Rod

Lubricate at end of cylinder rod. 1 fitting.

(22)Transfer Gear Drive Shaft

Lubricate telescopic shaft at lower end. 1 fitting.

(23)Ripper-Scarifier Trunnion Block Bearings

Lubricate bearings on both sides of each block. Total 4 fittings.

(24)Ripper-Scarifier Linkage Pins

Lubricate 4 fittings on each side.

(25)Top Of Circle

Apply grease with paddle.